All were produced from May 1, 2012, to Feb. The manufacturer was not notified. It could allow a driver to start the Elantra without pressing the brake pedal. I can hit the slightest bump and it will rattle and shake like I ran over a huge pot hole. The recall number from this site is 09v280000.
The vehicle was not repaired. The vehicle was taken back to the dealer where it was diagnosed that the front and rear rotors and pads needed to be replaced. I find it hard to believe that something as critical and safety oriented as a switch that controls the brake light function of your vehicle could fail twice within a 6 year period. When the brake pedal was depressed, the brake lights failed to illuminate. Then swing the access panel closed to complete the job.
Due to the manufacturer the contact had the dealer replace the stop lamp switch. I was almost rear-ended when I hit the gas but the car decided it wanted to suddenly slow down a few seconds later. Fountain Valley, California — Dec. Two of the 10mm nuts are accessible from the edge of the trunk lid and the other two are in the recessed cut out. The manufacturer was not made aware of the failure. Replace the trunk lid carpeting and insert the black plastic pop rivet fasteners. The contact stated that the brake lights failed to illuminate when applied and there was a progressing failure in which the gear would not shift out of park to change over into another gear.
I looked up on the internet to see if there was any way to fix it and I found the recall on this particular item. Brake light bulbs grow dimmer over time and eventually burn out. And unlike parts-store replacements, All our Hyundai Parts are designed specifically for Hyundai models, so they'll fit properly and install easily. It could allow the car's stop lights to remain illuminated long after the brake pedal has been released. I would like this to be reviewed further and I would like Hyundai to cover our repair cost for this defective part.
The manufacturer was also notified and stated that there were no recalls addressing the failure. I put the car back in park and turned it off, then finally on the third try, the engine engaged and I had control of the car, moved back into the parking place and then managed to back out normally and proceed. The contact stated that she had to depress the brake pedal with full force to stop the vehicle. The contact stated that the vehicle stalled and failed to restart. The campaign id for the latest recall is 13v113000. The mechanic stated that he could not believe our vehicle wasn't covered under the recall because he has had alot of vehicles with that same issue.
Our Hyundai Elantra light bulb guides allow you to easily replace light bulbs, replace headlight bulb, change a broken lightbulb, install a hid headlight conversion or install led light bulbs instead of spending countless hours trying to figure out which light bulb sizes in your 2012 Hyundai Elantra. The manufacturer was not notified. According to Hyundai customer service this problem was repaired on March 09, 2010. The contact stated that while driving at various speeds, someone alerted her and advised her that the brake lights were not illuminated. As I backed out of a parking place and attempted to stop the car in reverse to check the area behind me, the car stalled out completely, the engine stopped and the brakes would not respond and seemed stuck.
We took her car to the local mechanic to get repaired. The vehicle was taken to the dealer on numerous occasions where it was diagnosed that the front driver side sway bar needed to be replaced. Line up the screw ends on the trunk lid tail light housing with their respective holes and gently re-install the housing. . I cannot upload video let me know if you need. Grateful for that person, who may have saved our lives. Replace it with a five watt T10 wedge base bulb also known as part 168 or 194.
If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal. The approximate failure mileage was not available. Unfortunately this applies to the 2007 Elantra and I have the 2006. The vehicle was driven to the dealer where they were unable to locate a failure. The contact drove the vehicle to an auto part store, but the employee could not determine what fuse the vehicle needed. The vehicle was repaired but not under the manufacturers recall.
The contact stated that the steering wheel became difficult to turn and the brakes felt spongy. I started the car and pressed the brake a few times but the lights remained on so I thought the switch had gone bad. Please help support this website by shopping at. Timeline of Events On July 25, 2016, Hyundai decided to begin an initial recall on brake pedal stopper pads in certain Hyundai Elantra Sedans from the 2013 model year, but also continued analysis going forward. The vehicle was towed to a dealer where it was diagnosed that the electronic stability control module needed to be replaced. I request to look into this reaching out to company and address this issue. It could cause the car's traction control warning lamp to light up.
It was issued by Hyundai-kia America technical center inc. Obviously from all the complaints I see online this recall needs to be expanded. The contact stated that when the brakes were applied, the rear brake lights would not illuminate. Dealers will receive formal recall notifications starting Feb. Don't waste your time wasting ours! While driving down a hill or making a turn at various speeds, there was an abnormal sound emitting from the vehicle.